Terra Metals has extended the strike of its Southwest PGM-copper-nickel discovery to approximately 1,500 metres, including a 600-metre expansion of shallow mineralisation. Broad near-surface and deep intersections support the company’s push towards a maiden resource estimate in early 2027, although true widths, continuity and recoveries remain unconfirmed.
- Southwest mineralised strike extended to approximately 1,500m
- 600m extension of shallow, surface-reaching mineralisation
- 205m at 1.07g/t 3E from 4m in SWDD112
- 205.8m at 0.88g/t 3E at depth in SWRD025
- Maiden Southwest MRE targeted for Q1 2027
Southwest discovery reaches 1.5km of strike
Terra Metals Limited (ASX:TM1) has added 600 metres to the shallow, surface-reaching mineralisation at its Southwest discovery in Western Australia, taking the interpreted mineralised strike to approximately 1,500 metres. The system remains open along strike and down dip, with mineralisation extending as far as 750 metres down dip and an interpreted width of up to approximately 400 metres.
The latest results build on the company’s 1.35km Southwest extension, which was reported after 76,000 metres of drilling. Terra says more than 30,000 metres of results from this year’s drilling are still outstanding, while four rigs are expected to continue drilling at Southwest through December.
Broad mineralisation starts close to surface
The eastern extension delivered some of the strongest near-surface intervals in the release. Diamond hole SWDD112 returned 205 metres at 1.07g/t 3E, 0.17% nickel and 0.11% copper from just four metres, including nine metres at 3.47g/t 3E from 178 metres. Reverse-circulation hole SWRC107 produced 236 metres at 0.97g/t 3E and 0.16% nickel from 20 metres, with a 26-metre zone grading 1.83g/t 3E.
Nearby drilling also extended the mineralised footprint to the north. SWRC185 returned 57 metres at 1.09g/t 3E from 20 metres, while the northernmost holes reported, SWRC164 and SWRC165, intersected shallower but lower-grade mineralisation over a combined 600-metre extension. Terra says the near-surface geometry could be relevant to potential open-cut mining methods, but geological modelling will be needed to establish continuity and true widths.
Deep drilling adds scale beneath the Main Sulfide Zone
The release also carries a second message: Southwest is not confined to shallow mineralisation. A diamond tail on SWRD025 intersected 304 metres of cumulative mineralisation across three zones, including 205.8 metres at 0.88g/t 3E from 472.3 metres. Within that interval was an 83.5-metre zone at 1.43g/t 3E and a 1.1-metre higher-grade section at 9.56g/t 3E, alongside nickel and copper.
Further deep results from SWRD086 included 112.4 metres at 0.80g/t 3E from 430 metres, with 12 metres at 3.01g/t 3E. In the Main Zone, SWRC130 returned 129 metres at 1.10g/t 3E from 171 metres to the end of the hole, while SWRC128 and SWRC129 also ended in mineralisation. Those end-of-hole results leave the full down-dip extent unresolved rather than proving that the intervals continue indefinitely.
Resource estimate remains the next test
Terra plans to incorporate the new assays into its geological and structural models before delivering a maiden Southwest Mineral Resource Estimate targeted for the first quarter of calendar 2027. A Scoping Study is planned during 2027, with the company reporting A$57.9 million in cash at 30 September 2026 to fund the next phase of drilling and technical work.
The exploration results are encouraging in scale, but they are not yet an economic resource. The reported intersections are downhole lengths, not confirmed true widths; actual metallurgical recoveries remain to be established; and the resource classification, grade distribution and continuity are still under review. The next meaningful test will be whether the expanding drill pattern converts a large collection of intersections into a coherent, mineable geological model.
Bottom Line?
The 1.5km footprint and persistent deep mineralisation strengthen the exploration case, but the Q1 2027 resource estimate must establish how much of that scale is continuous, recoverable and economically relevant.
Questions in the middle?
- How much of the reported downhole mineralisation will translate into true widths suitable for resource classification?
- Will metallurgical testwork confirm recoveries that support the PGM, nickel and copper mix?
- Can the planned Q1 2027 resource estimate convert the open-ended drilling results into a coherent economic envelope?